 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications Rev.c -- 23-04-2007 Preliminary data sheet 1. General description TD1600ALF-4 belong to the new generation of terrestrial tuners designed to cope with digital COFDM and analog transmission standards. From function point-of-view these tuners can be divided into two high-frequency sections, a RF-loopthrough and a single conversion tuner part. In the loopthrough section broadband low-noise amplifiers are used. The loopthrough frequency response covers the entire frequency range from VHF to UHF. The RF-downstream section is equipped with a state-of-the-art single conversion tuner, which makes use of a highly integrated MOPLL IC that provides the required high level of performance necessary for COFDM signal processing. The tuners are provided with a DC/DC converter to generate the tuning voltage internally. The internal 4MHz PLL crystal reference frequency is fed through one of the pinnd terminals and can be used as a clock for a 2 device e.g. the channel decoder. Two IF-outputs are provided, one is a wideband, non filtered IF-output, while the other, narrow-band IF-output is equipped with a SAW-filter and a gain controllable IF-amplifier. This narrow-IF-output matches the A-to-D converter input of currently available channel decoders. All tuners out of this family can be equipped with two standard IEC-connectors, RF-in is IEC-female, RF-out is IEC-male. The tuner housing is available in a vertical or horizontal mountable execution; the pinning pitch corresponds to the World Standard Pinning convention. Apart from the RF-connectors, all other terminals are made with wire pins at the bottom side of the tuner. NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications Table 1. Parameter Frequency allocation table TD1611ALF-4/ TD1311ALF-4 174 MHz - 230 MHz 474 MHz - 858 MHz (*) TD1344ALF-4 474 MHz - 858 MHz (*) RF frequency range Channel bandwidth RF-loopthrough range IF-center frequency RF input connector RF output connector (*) 7/8MHz ch E2 - ch E69 36.16 MHz IEC female IEC male 8 MHz ch E2 - ch E69 36.16 MHz IEC female IEC male data refer to RF-channel center frequency. 2. Features * * * * * * * * * * * * * * * * * * * * * * * * TD1600ALF-4 Highly integrated RF-module, 3-band tuner plus active loopthrough +5V supply voltage only; no external tuning voltage required Tuners for horizontal and vertical mounting available Option with DC - power output through input connector (e.g. indoor antenna supply) Tuners comply with relevant CENELEC standards with regard to requirements concerning signal handling capability and immunity Superior low noise and high sensitivity performance RF-in to RF-out loopthrough amplifiers Low noise and excellent linearity Full VHF to UHF frequency range coverage Standard connectors for in- and output e.g. IEC, F-connector, RCA High performance and cost effective single conversion tuner I2C programmable 400kHz Bus compliant Fast PLL tuning speed (programmable step size e.g. 62.5kHz and 166.67kHz) Tuner internal gain control loop with selectable TakeOverPoint settings via I2C Bus External gain control possible with internal loop disabled 4.0V (max. gain) to 0V (min. gain) gain control voltage Flat overall frequency response High PLL loop bandwidth which ensures very low oscillator phase noise 4 MHz crystal reference frequency output SAW-filter and IF-amplifier included Switchable 7/8 MHz SAW filter Fixed 8 MHZ SAW filter IF-amplification controllable over a wide range (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 2 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications * Differential, filtered (SAW) `digital' IF-output to directly drive the channel decoder 3. Ordering information Table 2. Ordering information Table description (optional) Type number Package Name Description Version TD1611ALF/IVP-4 3112 297 15531 VHF 3 - UHF PLL tuner, Loopthrough, antenna power, Screw hole, DC/DC converter, IEC connector, vertical mount VHF 3 - UHF PLL tuner, Loopthrough, antenna power, Screw hole, DC/DC converter, IEC connector, horizontal mount VHF 3 - UHF PLL tuner, Loopthrough, antenna power, DC/DC converter, IEC connector, vertical mount VHF 3 - UHF PLL tuner, Loopthrough, antenna power, DC/DC converter, IEC connector, horizontal mount UHF only PLL tuner, loopthrough, antenna power, Screw hole, DC/DC converter, IEC connector, vertical mount UHF only PLL tuner, Loopthrough, antenna power, Screw hole, DC/DC converter, IEC connector, horizontal mount UHF only PLL tuner, Loopthrough, antenna power, DC/DC converter, IEC connector, vertical mount UHF only PLL tuner, Loopthrough, antenna power, DC/DC converter, IEC connector, horizontal mount TD1611ALF/IHP-4 3112 297 15521 TD1311ALF/IVP-4 3112 297 15491 - TD1311ALF/IHP-4 3112 297 15481 - TD1644ALF/IVP-4 3112 297 15631 - TD1644ALF/IHP-4 3112 297 15621 - TD1344ALF/IVP-4 3112 297 15511 - TD1344ALF/IHP-4 3112 297 15501 - TD1311AF/PHP-4 3112 297 15691 VHF 3 - UHF PLL tuner, antenna power, DC/DC converter, phono connector, horizontal mount TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 3 of 27 TD1600ALF-4 Vtune . 33V PLL AGC loop 5V DC-power for indoor antenna AGC (2) +5V tuner supply voltage ( 7) I C - BUS (4/5) 2 4MHz crystal reference M O P LL Preliminary data sheet NXP Semiconductors 4. Block diagram low-band low osc. AGC loop mid-band mid Fig 1. Block diagram of TD1616ALF osc. high high-band RF-input Rev.c -- 23-04-2007 osc. SAW RF- output reference IF - output IF - AGC IF - output frequency (broadband) (narrowband) output (6) (8) (9) (10/11) Tuner module for digital terrestrial (OFDM) applications (c) NXP B.V. 2006. All rights reserved. (1) TD1600ALF-4 4 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications 5. Pinning information 5.1 Pinning Fig 2. Pinning diagram 5.2 Pin description Table 3. Pin description Table description (optional) Pin 1 2 3 4 5 6 7 8 9 10 11 [1] [2] [3] [4] [5] Description DC-power option for tuners with P-extension [1] External RF-gain control voltage (0.5V - 4.0V) PLL chip address select (I2C / tuner) [3] SCL (I2C / tuner) SDA (I2C / tuner) 4MHz reference frequency output [4] +5V 5% supply tuner (VTU) 'broadband' IF - output[4] IF-gain control voltage [5] 'narrowband' IF - output 1[4] 'narrowband' IF - output 2[4] Max. permissible current: 35mA Max. permissible control voltage source impedance limited to 200ohms (see application notes) see application notes AC coupled max. gain at 3V,min. gain at 0V (see application notes) [2] TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 5 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications 6. Limiting values Table 4. Limiting values under non-operational conditions Table description (optional) Symbol TAMB RH gB gS Avib Parameter Ambient temperature Relative humidity Bump acceleration Shock acceleration Vibration amplitude 25g 50g 10Hz to-55 Hz Conditions Min -25 Max +85 95 245 490 0.35 Unit C % m/s2 m/s2 mm 7. Static Characteristics Table 5. Static characteristics TAMB = -10C to +60C, RH=95 Symbol Parameter VL DC-loopthrough to input connector Max. permissible current Tuner supply voltage Relevant supply current Tuner AGC input voltage Conditions Optional Min Typ Max 20 Unit V IL VTU ITU VAGC 4.75 180 - 5.00 200 4.0 35 5.25 210 4.5 mA V mA V VAGC IAGC AGC input voltage range AGC control current at 0V AGC voltage 0.3 -2 - 4.0 - V mA VIF-AGC VIF-AGC IIF-AGC VAS IF- AGC input voltage IF- AGC input voltage range IF- AGC input current Address select input voltage Serial clock input voltage Serial data input voltage Serial data input current 0 3.0 - 4.0 3.5 V V A V - - 10 5.25 VSCL VSDA ISDA -0.3 -0.3 -1 - 5.25 5.25 5 V V mA TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 6 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications 8. Dynamic Characteristics Next specification data refer to the overall performance from RF-input to IF-output. If not otherwise stated, all data are assigned to broadband IF-output. The tuner has to be tuned as such that coincidence between RF-channel center and IFcenter frequency of 36.16 MHz is given. Table 6. Dynamic characteristics Tamb = 22C 2C; RH =60%10%; VTU=5V0.1V; VRF_AGC=4.0V0.1V(internal AGC detector disabled):VIF_AGC =1V(maximum); Zi(RF) = 75; Zo(RF)=75; unless otherwise stated. Parameter Frequency ranges (1) Conditions TD1611 (VHF high) TD1611 (UHF) TD1644 (UHF) Min 174 470 470 47 Typ Max 230 862 862 Unit MHz MHz MHz dB dB dB dB dB RF power gain (2) 50 6 Overall gain taper RF AGC range Low band Mid band High band Image rejection (Referred to IF-center frequency) Osc. voltage at aerial input In-channel return loss (3) Overloading causing 1dB gain compression Noise figure ESD protection of terminals Surge protection at RF-input Osc. phase noise (4) At 1 kHz At 10 kHz Overall voltage gain [1] [2] [3] [4] [5] TD1600ALF-4 40 40 35 66 55 70 60 <20 5 7 76 VHF high (mid band) UHF (high band) (f < 1000MHz) dB dB dBV dB dBV at nom. gain 2 5 5 6 dB kV kV -88 -90 70 -78 -82 dBc/Hz dBc/Hz dB (5 channel center including tuning margin to be measured at `broadband' IF-output with 75ohms load to be measured at RF-input in the range channel-center 3MHz PLL step size 166.667kHz / 148.86kHz; CP as recommended (see application notes) measured at terminals 10/11; IF-AGC voltage (terminal 9) set to 3V (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 7 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications Cross-modulation: Definition: The cross-modulation is defined as the transfer of the adjacent channels' modulation depth to the wanted carrier. Measurement: Unwanted carriers (funw) Level of all carriers Modulation = wanted carrier (fw) 8MHz = 70dBV = AM, 50%, 15kHz IF-output loaded with 1k // 15pF // 1.2uH (load compensation) IF-output level limited to 104dBV Spec. limit: max. cross-modulation is less or equal 1% (typ. 0.3%) Flatness (tilt) of overall responds curve (to be measured at broad-band IF-output): Definition: tilt of curve is defined in the specified IF-range from highest to lowest gain point at nom. gain Measured at broadband IF-output: * * in the range IF-center 3MHz in the range IF-center 4MHz : 3dB max. : 4dB max. Deterioration of flatness during AGC (0dB to 30dB): 1.0dB max. . dB +6 +4 +2 0 . . -2 -4 -6 -3.0 -4 36.00 . +3.0 +4 MHz Fig 3. Flatness (tilt) of overall responds curve TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 8 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications . . 10dB/ 10dB/ . Center 36.13MHz 1.5MHz/ Span 15MHz . Center 36.13MHz 1.5MHz/ Span 15MHz a. 7MHz wide SAW-filter selected b. 8MHz wide SAW-filter selected Fig 4. Typical response curves at narrowband IF-output 8.1 Input sensitivity: The typical input sensitivity, when measured in an adequate application (i.e. Philips Semiconductors COFDM reference board OM5754) is: - 82dBm , BER 2x10- 4 post Viterbi Conditions: Gaussian channel w/o added noise, 8k OFDM, 64QAM, code rate 2/3, guard interval 1/8 8.2 4MHz reference output (terminal 6): Frequency accuracy Max. permissible load Output level [0C - 60C ; supply voltage (terminal 7) +5V5% ; loaded with min. t.b.d.] Phase Noise @ 1kHz : -104dBc/Hz typ. : 80ppm max. : t.b.f. : 440mVpp typ. TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 9 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications 8.3 Overall performance from RF input to RF output Table 7. Overall performance from RF input to RF output Specification data refer to the overall performance from RF-input to RF-output. (valid for all tuners out of this family) Parameter Frequency range (referred to channel center) Power gain Overall gain taper Noise figure (tuners w/o remod) CSO / CTB (acc. EN50083) RF-output return loss (referred to 75) 10 dB -57 Min 51 0 2.5 5 Typ Max 858 3 Unit MHz dB dB dB dBc 9. Application information 9.1 Programming of tuner PLL The tuner control (frequency selection and band switching) is done via the I2C bus. One address byte and four data bytes are needed to fully program the tuner. A PLL lock flag can be read from the tuner during 'READ' - mode. Four independent PLL addresses are available; which one is actually valid depends on the address select voltage that is connected to terminal 3. TD1300ALF tuners comply to the 5V I2C - Bus specification. Table 8. Name ADB DIV1 DIV2 CB1 -bus data format ' WRITE ' - mode: Description Address byte Divider byte1 Divider byte2 Control Data Byte1 Control data byte2 7 1 0 N7 1 1 CP2 6 1 N14 N6 5 0 N13 N5 4 0 N12 N4 0 0 SP5 3 0 N11 N3 1 ATC SP4 2 CA1 N10 N2 R2 AL2 SP3 1 CA0 N9 N1 R1 AL1 SP2 0 ACK R/W=0 A N8 N0 R0 AL0 SP1 A A A A A D/A=1 0 D/A=0 0 CP1 CP0 CB2 TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 10 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications Description of used symbols Description Chip address selection bits[1] Read/write bit LO frequency divider bits D/A = 1 following 6 bits contain test and reference divider ratio data D/A = 0 following 6 bits contain AGC setting data Bit = 0 (write mode), bit = 1 (read mode) Conditions Table 9. Symbol CA1, CA0 R/W N14 to N0 D/A R2, R1, R0 SP5 ..... SP1 Reference divider bits [2] Band selection and SAW filter switch ports AGC time constant data bit; only valid with int. AGC loop active ATC = 1 enables fast tuning speed during channel search mode ATC = 0 recommended after channel acquisition; normal mode ATC AL2, AL1, AL0 AGC Take-Over-Point bits [3] CP2, CP1, CP0 SP5 - SP1 PLL charge pump current selection [4] bits Switch ports [5] bit = 1 port Vout is 'ON' bit = 0 port Vout is 'OFF CA1, CA0 [1] [2] [3] [4] [5] Programmable address selection bits [6] See table: Programmable address selection See table: Reference Divider Settings see table: Internal AGC loop TOP see table: Charge Pump Settings see table: Band and SAW-filter selection table Table 10. CA1 0 0 1 1 Programmable address selection bits (CA1, CA0) CA0 0 1 0 1 Voltage applied to terminal 3 0V to 0.1x VTU Terminal open 0.4xVTU to 0.6xVTU 0.9xVTU to 1.0xVTU TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 11 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications N14 to N0: programmable divider bits divider ratio: N = N14x214 + N13x213 + ... + N1x21 + N0 How to calculate the divider ratio N : N= (f input + f IF ) Hz Hz f ref whereby f ref = f ref = f ref = 4 10 6 [Hz ] = 62.5kHz 64 (1) 4 10 6 [Hz ] = 166.67kHz 24 (1) 4 106 [Hz ] = 142.86kHz 28(1) Note (1) : divider ratio to be set with Bits ' R2 ..... R0 ' (see table below) Do not set the divider ratio as such that the tuner is tuned into extreme conditions i.e. far below or far above the specified ranges. R2, R1, R1: PLL reference divider settings (Control Data Byte 1): Important note: in order to avoid instabilities of the reference divider it is advisable to set the reference divider in combination with the IF-frequency and channel spacing as per below table Table 11. PLL step size (kHz) 142.86 166.67 PLL reference divider settings (Control Data Byte) PLL ref. divider ratio 28 24 R2 0 0 R1 0 1 R0 1 0 IF frequency (MHz) 36.16 36.16 Channel spacing (MHz) 8 6 and 7 AL2, AL1, AL0: AGC Take-Over-Point bits (Control Data Byte 1): External AGC mode: The tuner can be controlled by an external gain control voltage applied to terminal 2 of the tuner. In that case the ALx - bits need to be set as shown in table below. The impedance of the control voltage source should not exceed 200ohms. TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 12 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications External AGC mode setting AL1 0 0 1 1 0 0 1 1 AL0 0 1 0 1 0 1 0 1 Typical TOP level 124dBuV 121dBuV 118dBuV 115dBuV 112dBuV 109dBuV IAGC = 0 VAGC = 3.5V External AGC (1) Loop disabled (2) Remarks Table 12. AL2 0 0 0 0 1 1 1 1 [1] [2] The tuner internal AGC current sources are disabled (default mode after power on reset). The tuner internal AGC detector is disabled. With no external AGC voltage applied to the tuner, the RFgain is always set to maximum. CP2, CP1, CP0: PLL charge pump current settings Note: during search tuning it is recommended to set the PLL to a moderate charge pump. To enable best oscillator phase noise performance during digital signal processing, the PLL charge pump current should be set to conditions as given with following table. Table 13. CP2 0 0 0 CP1 0 0 1 PLL charge pump current settings CP0 0 1 0 Typical CP current (uA) 40 60 90 Recommendations To be used during search tuning and for 50kHz, 62.5kHz PLL step sizes Low band: 87MHz to 130MHz 0 1 1 130 Mid band: 200MHz to 290MHz High band: 480MHz to 620MHz 1 0 0 190 Low band: 130MHz to 160MHz 1 0 1 280 Mid band: 290MHz to 420MHz High band: 620MHz to 830MHz 1 0 1 280 Low band: 130MHz to 160MHz Mid band: 290MHz to 420MHz TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 13 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications 1 1 0 410 Low band: >160MHz(*) Mid band: >420MHz(*) 1 1 1 600 High band: >830MHz (*) (*) oscillator frequencies Table 14. Band Low - band Mid - band High - band SP5 ......SP1 Band and SAW-filter selection table SP5 0 0 0 0 0 SP4 X X X 0 1 SP3 0 0 1 X X SP2 0 1 0 X X SP1 0 0 0 X X 7 MHz SAW filter 8 MHz SAW filter Table 15. I 2C-bus data format, ' READ ' - mode 7 1 POR 6 1 FL 5 0 0 4 0 1 3 0 AGC 2 CA1 1 1 CA0 0 0 ACK Description Address byte Status byte A : Acknowledge R/W=1 A 0 A CA1 / CA0 = chip address (see address selection table) POR= power-on-reset-flag ; POR = 1 after power-on FL= in-lock-flag ; FL = 1 when PLL is phase locked AGC= internal AGC flag ; AGC = 1 when internal AGC is active TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 14 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications Timing of program sequences: Because of the Tuner - PLL frequency divider settling time of min. 60usec. , the occurrence of any other I2C traffic start condition present within that periode on the Bus will disturb the divider and result in a not properly tuned tuner VCO. Each time the Tuner-PLL frequency divider has been programmed, a 60usec wait becomes necessary before continuing the I2C bus traffic. . START Tuner PLL-chip address Divider Byte 1 Divider Byte 2 Date Byte 1 Data Byte 2 STOP 60 usec START START . any other IIC device Tuner PLL-chip address Modulator-PLL address Tuner PLL-chip address data Date Byte 1 Divider Byte 1 data data Data Byte 2 Date Byte 1 data STOP STOP . START START Divider Byte 2 Data Byte 2 STOP STOP Divider Byte 1 Divider Byte 2 60 usec . Fig 5. Program sequence 9.2 Max. Permissible IF-load impedance: The max. load applied to the ' broadband ' IF-output of the tuner should not exceed: 2k min.//15pF max. The reactive load has to be compensated (tuned-out to the IF-center frequency) by an inductance connected in parallel to the load. The max. load applied to the ' narrowband ' balanced IF-output of the tuner is limited to 1k min. TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 15 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications 9.3 Gain control characteristics of IF amplifier 3.50 3.25 3.00 2.75 2.50 2.25 2.00 1.75 1.50 1.25 1.00 0.75 0.50 0.25 . 0.0 -10.0 gain reduction [dB] -20.0 -30.0 -40.0 -50.0 -60.0 -70.0 -80.0 -90.0 gain control voltage at terminal 9 [V] Fig 6. Gain control characteristic of IF-amplifier (terminal 9) . VD . terminal 9 330R 1k 1nF IF-amplifier . (1) With an IF-gain control voltage of about 1.3V applied to terminal 9 of tuner, the narrowband IF-output level is about the same of the broadband IF-output. Fig 7. Internal AGC circuit TD1600ALF-4 Preliminary data sheet Rev.c -- 23-04-2007 0.00 (c) NXP B.V. 2006. All rights reserved. 16 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications . TD1600AL F . AGC pin 2 1k . 100R 5V IAG C <15uA 1.2k AGC control voltage . Note: In case the above recommended AGC control voltage source is not used, alternatively a control voltage source with a max. 200ohms impedance can be used Fig 8. External RF-Gain Control Voltage; recommended schematic 9.4 Phase noise, I2C bus traffic and crosstalk The low noise PLL used in these tuners will clean up the noise spectrum of the VCOs close to the carrier to reach noise levels @ 1 kHz offset from the carrier compatible with e.g. OFDM reception. Linked to this noise improvement, some disturbances may become visible while they were not visible because they were hidden into the noise in analog dedicated applications and circuits. This is especially true for disturbances coming from the I2C bus traffic, whatever this traffic is intended for the MOPLL or for another slave on the bus. To avoid this I2C bus crosstalk and be able to have a clean noise spectrum, it is necessary to use a bus gate that enables the signal on the bus to drive the MOPLL. This is used only when the communication is intended for the tuner part (such a kind of I2C bus gate is included into the Philips terrestrial channel decoders), and to avoid unnecessary repeated sending of the same information. 9.5 Main board recommendations: The tracks on the main board connected to the tuners' terminals should be kept as short as possible in order to avoid interferences because of immunity problems and/or to avoid problems with regard to radiation of the local oscillator. TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 17 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications 9.6 For tuners with antenna-power function (tuners with type name extension "P") Attention: Modules with type name extension 'P' do have the DC-supply option through out the RFinput connector on board. The max. permissible current drive has to be limited to 35mA . Should this option be used in the end application, it is recommended that an electronic switch with some current protection circuitry be employed, to avoid damage to the tuner itself. TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 18 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications 10. Package outline (1) Fig 9. Package outline of TD1600ALF-4 TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 19 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications Fig 10. Package outline of TD1600ALF-4 TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 20 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications Fig 11. Package outline of TD1300ALF-4 TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 21 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications Fig 12. Package outline of TD1300ALF-4 TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 22 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications 11. Packing information The products are packed in the carton box and transferred to customers by Pallet Transport. w h b Carton Boxes are made of Corrugated Fibreboard which are free of environmentally banned substances. Fig 13. Example of carton box Table 16. Package information Table description (optional) Package Carton vertical Pallet vertical Carton horizontal Pallet horizontal Dimension L x W x H (cm) 46 x 34 x 7.5 120 x 105 x 105 46 x 34 x 9.4 120 x 105 x 105 Number of sets 98 7742 60 3900 Gross weight (kg) 4.09 345.1 3.16 227.4 TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 23 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications 12. Mounting (1) Fig 14. Punching pattern of chassis PCB TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 24 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications 13. Revision history Table 17. Revision history Table description (optional) Document ID TD1600ALF-4 Modifications TD1600ALF-4 Modifications Release date 2007-01-19 Data sheet status Objective data sheet Change notice Rev aSupersedes - 2007-03-23 * * * * * Preliminary data sheet Rev b Rev a Mechanical drawings updated to NXP cover Packaging information updated Supply voltage and performance data updated Change status to Preliminary TD1644ALF/IVP-4 and TD1644ALF/IHP-4 added Pg 2 - Add product 12nc Preliminary data sheet Rev c Rev b TD1600ALF-4 Modifications 2007-04-23 * New type TD1311AF/PHP-4 added in page 3 TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 25 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications 14. Legal information 14.1 Data sheet status Document status[1][2] Objective [short] data sheet Preliminary [short] data sheet Product [short] data sheet Product status[3] Development Qualification Production Definition This document contains data from the objective specification for product development. This document contains data from the preliminary specification This document contains the product specification [1] Please consult the most recently issued document before initiating or completing a design. [2] The term `short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 14.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is for the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 14.4 Licenses Purchase of NXP 14.3 Disclaimers General -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of a NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of 14.5 Patents Notice is herewith given that the subject device uses one or more of the following patents and that each of these patents may have corresponding patents in other jurisdictions. 14.6 Trademarks Notice: All referenced brands, product names, service names and trademarks are property of their respective owners. I2C-bus -- logo is a trademark of NXP B.V. 15. Contact information For additional information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com TD1600ALF-4 (c) NXP B.V. 2006. All rights reserved. Preliminary data sheet Rev.c -- 23-04-2007 26 of 27 NXP Semiconductors TD1600ALF-4 Tuner module for digital terrestrial (OFDM) applications 16. Contents 1. 2. 3. 4. 5. 5.1 5.2 6. 7. 8. 8.1 8.2 8.3 9. 9.1 9.2 9.3 9.4 9.5 9.6 10. 11. 12. 13. 14. 14.1 14.2 14.3 14.4 14.5 14.6 15. 16. General description.............................................1 Features ...............................................................2 Ordering information ..........................................3 Block diagram......................................................4 Pinning information ............................................5 Pinning ..................................................................5 Pin description.......................................................5 Limiting values ....................................................6 Static Characteristics..........................................6 Dynamic Characteristics ....................................7 Input sensitivity:.....................................................9 4MHz reference output (terminal 6):......................9 Overall performance from RF input to RF output.10 Application information ....................................10 Programming of tuner PLL ..................................10 Max. Permissible IF-load impedance: .................15 Gain control characteristics of IF amplifier ..........16 Phase noise, I2C bus traffic and crosstalk ...........17 Main board recommendations: ............................17 For tuners with antenna-power function (tuners with type name extension "P")..........................18 Package outline .................................................19 Packing information..........................................23 Mounting ............................................................24 Revision history ................................................25 Legal information ..............................................26 Data sheet status ................................................26 Definitions............................................................26 Disclaimers..........................................................26 Licenses ..............................................................26 Patents ................................................................26 Trademarks .........................................................26 Contact information ..........................................26 Contents.............................................................27 Please be aware that important notices concerning this document and the product(s) described herein, have been included in the section `Legal information'. (c) NXP B.V. 2006. All rights reserved. For more information, please visit: http://www.nxp.com. For sales office addresses, email to: salesaddresses@nxp.com. Date of release: 23-04-2007 Document identifier: TD1600ALF-4 |
Price & Availability of TD1611ALFIHP-4
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |